Galicaster Mobile Installation Guide

{pop-away:metadata | comments | children | labels}


h1. Introduction

{section}
{column:width=59%}
On this section you will be guided through a series of steps to finish the setup of your Galicaster Mobile unit. Please, read this documentation carefully and follow its instructions. In case of doubts please take advantage of the [Galicaster Community list|Galicaster:Community] to make any question or suggestion.

In the following sections you will receive instructions on how to connect and configure you Galicaster unit.

{column}
{column:width=38%}
* [A. Cards and connectors|#cards]
** [1. NTSC-based configuration|#ntsc]
** [2. SDI-based configuration|#sdi]
* [B. Capture Devices configuration|#gcconf]
** [1. Hauppauge configuration|#hau]
** [2. Blackmagic configuration|#bm]
** [3. Sound configuration|#sound]
* [C. Network configuration|#net]
* [D. Opencast Matterhorn Related configuration|#mh]
{column}
{section}

{anchor:cards}
h3. A. Cards and connectors
----

The Galicaster Mobile Unit comes equipped with different inputs to fulfill your needs on recording multistream material. Depending on the devices you are about to use you should combine those inputs properly.

There are two main combinations, depending on the type of camera (NTSC or SDI) you use to record the presenter. In both cases you have to use a VGA grabber to record the slides. Those combinations will be explained briefly on the next two sections.

Please, take a closer look to the image to identify the ports of each capture card before connecting anything.
{section}
{column: 59 %}
h5. a.Graphics card

|| \# ||Port || Description||
| A1 | *VGA output* | To connect the monitor of the computer.|
| A2 | *HDMI output* | To connect the monitor of the computer.|
| A3 | *DVI output* | To connect the monitor of the computer.|

h5. b.Blackmagic card

|| \# ||Port || Description||
| B1 | *Deck port* | To connect a control desk via RS-422 interface.|
| B2 | *SDI output* | To connect an auxiliary monitor for the SDI video.|
| B3 | *SDI input* | To connect the video camera, BNC connector.|
| B4 | *Ref IN* | To connect a refference signal the monitor of the computer.|

{column}
{column: 39 %}
!ports.png|align=center,thumbnail,width=400,border=1!
{center}Click on the image to enlarge.{center}
{column}
{section}


h5. c.Hauppauge card

|| \# ||Port || Description||
| C1 | *Antenna input* | For TV tunning purposes, coaxial wire.|
| C2 | *S-Video input* | To connect the video camera, 4-pin connector.|
| C3 | *Composite input* | To connect the video camera, RCA connector.|
| C4 | *Audio input* | To connect a mixer or a microphone to record, mini-jack 3.5mm.|
| C5 | *IR input* | To connect an IR receptor for a remote control.|

h5. d.Epiphan card
|| \# ||Port || Description||
| D1 | *VGA capture* | To connect a laptop or computer VGA output to capture it |


h5. e.On-board sound card

|| \# ||Port || Description||
| E1 | *Line IN* | (Recommended) To connect a mixer or a line level microphone to record, mini-jack 3.5mm.|
| E2 | *Headphones OUT* | To connect a mixer or a microphone to record, mini-jack 3.5mm.|
| E3 | *Microphone IN* | To connect a microphone to record, mini-jack 3.5mm.|

h5. f.Motherboard

| F1 | *Mouse-Keyboard* | PS2 connector for keyboard or mouse|
| F2 | *USB hub* | External USB 2.0 hub for multiple purposes.|
| F3 | *SPDIF input* | External USB 2.0 hub for multiple purposes.|
| F4 | *HDMI output* | *DON'T USE*.|
| F5 | *VGA output* | *DON'T USE*.|
| F6 | *USB hub* | External USB 2.0 hub for multiple purposes.|
| F7 | *LAN input* | To connect a RJ45 connector for network purposes.|
\\

{anchor:ntsc}
h4. A.1 NTSC based configuration
----
On this scheme you will be using a Epiphan VGA2USB LR to capture the presentation and a Hauppauge PVR-250 to capture a composite NTSC video camera. The sound will be recorded and synchronized by the Hauppauge card.

* Connect your monitor to an output of the Graphics card (A1 to A3)
* Connect the RCA or 4-pin connector from your camera. (C2 or C3)
* Connect a laptop or computer to the Epiphan input (D1)
* Connect a mixer or a line-level microphone to the Hauppauge Line input (C4)
* To monitore the sound connect a pair of headphones or speakers to the sound card green output (E3).

!rca_scheme.png|align=center,border=1,width=400,thumbnail!
{center}Click on the image to enlarge.{center}

Once you have everything connected jump to [section B|#hau] to configure the device and the audio.


{anchor:sdi}
h4. A.2 SDI based configuration
----
On this scheme you will be using a Epiphan VGA2USB LR to capture the presentation and a Blackmagic Deckling SDI to capture a SD-SDI or HD-SDI (720p or 1080p i.e.) video camera. The sound will be recorded via the sound card.

* Connect your monitor to an output of the Graphics card (A1 to A3).
* Connect the BNC connector from your camera. (B3)
* Connect a laptop or computer to the Epiphan input (D1).
* Connect a mixer or a line-level microphone to the sound card blue input (E1).
* To monitor the sound connect a pair of headphones or speakers to the sound card green output (E3).

!sdi_scheme.png|align=center,border=1,width=400,thumbnail!

{anchor:gcconf}
h3. B. Capture Devices configuration
----

Galicaster configuration is specified in two files _conf-dist.ini_ and _conf.ini_. You can download two different models of _conf.ini_ depending on the cards you are using:

* Blackmagic + Epiphan: [conf.ini | http://webfiler.teltek.es/webfiler/galicaster/configs/bm_mobile/conf.ini]

*Standard selection*
You have to choose between a list of standards. To list and select the standard, run in a shell:

{code:none}
v4l2-ctl -d /dev/haucamera --list-standards | grep Index -A 2
v4l2-ctl -d /dev/haucamera -s 0
{code}

*Input selection*
Depending on the input you are using you have to choose bettween S-Video (4-pin) and Composite (RCA). To list and select the input, run in shell:

{code:none}
v4l2-ctl -d /dev/haucamera -n | grep Input -A 1
v4l2-ctl -d /dev/haucamera -i 2
{code}

Inputs 1 and 3 are for 4-pin.
Inputs 2, 4 and 5 are for RCA.

{code:none}
gst-inspect-0.10 decklinksrc | grep Enum -A 20
{code}

Once you identified the format you want to capture, edit the _conf.ini_ file you've just downloaded. Search for the _track_ Blackmagic and change the parameters _input_ and _input_type_ for their right values. Some try-and-error may be neccessary since maybe you can't gather all the information from your video source.
The _p_ in 1080p stands for _progresive_
The _i_ in 1080i stands for _interlaced_

*Pulse input ( Line in):*
_If you are using the Hauppauge card please skip this section_
First of all, go to the Sound Manager (speaker icon on the top right corner of the desktop), select the input you are using and set the values to 100% volume, no amplification.
Later, if you have distortion on your audio input, edit the conf.ini and set _amplification = 1.0_ in the AudioSource device.

*Headphones output*
Regulate this slide bar to a comfortable sound level.

*Galicaster Vumeter*
Add this section in the _conf.ini_ file.

{code:none}
[audio]
min = -60
max = 0
{code}

If the NO SOUND dialog is coming in and out constantly, set a higher value on _min_, for example -40.

* Alsa Advanced configuration *

If you still experience problems after configuring the Sound Manager and your Mixer or Sound input device, you should take a look to ALSA.
Run _alsamixer_ on a shell and ensure that your device is not being amplified.
* Press F6 to select the input and F4 to go to the Capture section.

----

To change your IP settings, pleas read this [official Ubuntu guideline|https://help.ubuntu.com/10.04/internet/C/connecting-wired.html].

The Network Manager is on the top right corner, Right-button click on the double arrow icon.

!netmanager.png|align=left!

First of all, You need the admin host address, including the port. For example:

{code:none}
host = http://fakeadmin.matterhorn.com:80
{code}

You also need a *digest user* - a regular one won't work. There is a default digest account that should be replaced with your own values.

{code:none}
username= matterhorn_system_account
password= CHANGE_ME
{code}

You also need to set up a default workflow and its parameters. Scheduled recordings will have his own workflow and parameters, defined in the scheduling operation, but the recordings started manually won't. The usual parameters you have to set up are *captions* and *trimHold*, which default to *False*. The normal configuration is:

{code:none}
workflow = full
workflow-parameters = trimHold:true
{code}

If you set up more than one parameter:

{code:none}workflow-parameters = trimHold:true;captions=True{code}

Finally, you have to decide if your recordings will be recorded automatically or not. If you want to do so, set *default* to True. All the configuration together will look like:

{code:none}
[ingest]
active = True
default = False
host = http://fakeadmin.matterhorn.com:80
username = matterhorn_system_account
password = CHANGE_ME
workflow = full
workflow-parameters = trimHold:true
{code}

This piece of code must be written on one of the configurations file. Be aware that values in _conf.ini_ will overrule its equivalent in _conf-dist.ini_.