Galicaster is based on Open Source technologies.
The recommended OS for this release is Ubuntu 10.04 LTS.
The installation process consists of five steps: installing dependencies, checking configuration, downloading software, configuring and running.
h6. 1.\- Install dependences.
Galicaster requires the following software to be installed:
* Gstreamer
* python-setuptools and pip
* iCalendar
* pyCurl
* Capture card configuration tools
{code:none}
$ sudo apt-get install \
gstreamer0.10-ffmpeg gstreamer0.10-alsa gstreamer0.10-plugins-bad gstreamer0.10-plugins-bad-multiverse \
gstreamer0.10-plugins-base gstreamer0.10-plugins-base-apps gstreamer0.10-plugins-good \
gstreamer0.10-plugins-ugly gstreamer0.10-plugins-ugly-multiverse
$ sudo apt-get install python-pip python-setuptools
$ sudo pip install icalendar
$ sudo apt-get install python-pycurl
$ sudo apt-get install v4l-conf ivtv-utils guvcview
{code}
In ubuntu 11.04 and above is recommended installing v4l-utils instead of ivtv-utils.
h6. 2.\- Check configuration.
Launch the following commands from a shell to verify that all dependencies are installed:
{code:none}
$ python --version
Python 2.6.6
$ python -c "import pygtk; pygtk.require('2.0')"
$ python -c "import pygst; pygst.require('0.10')"
$ python -c "import pycurl"
$ python -c "import icalendar"
$ gst-launch v4l2src num-buffers=25 ! video/x-raw-yuv,width=800,framerate=24/1 ! ffmpegcolorspace ! xvimagesink
$ gst-launch v4l2src num-buffers=25 ! video/x-raw-yuv,width=800,framerate=24/1 ! ffmpegcolorspace ! x264enc pass=5 quantizer=22 speed-preset=4 profile=1 ! queue ! avimux ! filesink location=out.avi
$ file out.avi
out.avi: RIFF (little-endian) data, AVI, 800 x 600, ~24 fps, video: H.264 X.264 or H.264
$ rm out.avi
{code}
h6. 3.\- Download software
Download the software from [this site|http://webfiler.teltek.es/webfiler/galicaster/galicaster-1.0.0-rc.tgz].
Uncompress it using tar:
{code}
$ tar xzf galicaster-1.0.0-rc.tgz
$ cd galicaster-1.0.0-rc
{code}
h6. 4.\- Configure Galicaster
The values are in the file {{conf.ini}}:
Sections:
* {{basic}}
** {{repository}}: path to the working folder.
** {{admin}}: enables admin mode (True\|False)
** Example:
{code:none}
[basic]
repository = /mnt/videos/Repository
admin = True
{code}
* {{screen}}
** {{right}}: Name of the video device to be shown in the right screen (None to deactivate).
** {{left}}: Name of the video device to be shown in the left screen (None to deactivate).
** {{cursor}}: Shows or hides the cursor. (True\|False)
** Example:
{code:none}
[screen]
right = Epiphan
left = Hauppagge
cursor = True
{code}
* {{ingest}}
** The data to connect Galicaster to an Opencast-Matterhorn server.
** Example:
{code:none}
[ingest]
default = True
username = matterhorn_system_account
host = http://admin.matterhorn.es:8080
password = CHANGE_ME
workflow = full
{code}
* {{trackN}}
** Values common to all devices:
*** {{name}}: Name assigned to the device.
*** {{device}}: Device type. (v4l2\|vga2usb\|webcam\|hauppage\|pulse)
*** {{flavor}}: Matterhorn "flavor" associated to the track. (presenter\|presentation\|other)
*** {{location}}: Device's mount point in the system (e.g. /dev/video0).
**** For PulseAudio devices run:
{code:none}
$ pactl -list | grep "Source" -A 5
{code}
and use "Name:" as the {{location}} field.
*** {{file}}: The file name where the track will be recorded.
*** {{active}}: Whether the device will be played and recorded. (True\|False)
** Values in audio (pulse) devices:
*** {{playing}}: Indicates if the audio, apart from being recorded, is played. (True\|False)
*** {{vumeter}}: Activates data sending to the program's vumeter. (True\|False) Only one device should be activated.
*** {{amplification}}: Gstreamer amplification value: < 1 decreases and > 1 increases volume. Values between 1 and 2 are commonly used.
** Example:
{code:none}
[track1]
name = Hauppagge
loc2 = /dev/hauprevideo
loc3 = /dev/haupreaudio
location = /dev/haucamera
file = CAMERA.mpg
device = hauppage
flavor = presenter
active = False
[track2]
name = Epiphan
active = False
location = /dev/screen
file = SCREEN.avi
device = vga2usb
flavor = presentation
[track3]
amplification = 2.0
name = AudioSource
vumeter = Active
location = alsa_input.usb-046d_081d_96D1FD90-00-U0x46d0x81d.analog-mono
file = sound.mp3
device = pulse
flavor = presenter
active = False
playing = False
[track4]
name = Webcam
videocrop-left = 160
videocrop-right = 160
caps = image/jpeg,framerate=25/1,width=1280,height=720
active = False
location = /dev/webcam
file = CAMERA.avi
device = mjpeg
flavor = presenter
{code}
h6. 5.\- Running
Galicaster Class is launched with the command:
{code:none}
$ ./classexec
{code}
...